TXT Coat Aerosol

1K Texture Coat
TXT Aerosol Texture Coat
TXT Aerosol Texture Coat Black Aerosol - One Can

$34.99


Add On
Quantity


Calculate Shipping

TXT Texture Coating Aerosol is an Australian-designed and manufactured 1K paint, meaning it does not require an additional hardener. This versatile solution offers defence against impacts, scratches, rust and effects of moisture. Suitable for a wide range of applications from toolboxes and bar work, plastic trims and interior components. TXT Texture Coating Aerosol's advanced 1K formulation provides a protective coating, which adheres to metal, aluminium, fiberglass, plastic and wood. Please read Technical Data Sheet to ensure procedures are followed for adhesion success.

Choose your texture finish. Two nozzles included. Fine or coarse.

Easy and convenient. Ideal for touch up or small texture jobs. 

After a tougher paint? Check out our 2K TXT range.

(TXT_Aero_Parent)

SURFACE PREPARATION
Bare metal, aluminum and galvanized steel - abrade with a minimum 180P sandpaper. Clean surface with solvent based wax and grease remover or isopropanol, ensuring surface is free from dust, grease, oils and contaminants. 
TXT can be applied direct to metal however, for best corrosion protection we suggest using a suitable primer such as etch or epoxy direct to metal then applying TXT.
If allowing primer to fully cure, you will need to treat this as a cured painted surface and abrade the primer to ensure maximum adhesion.

Rigid Plastic / Fiberglass - abrade with a minimum 180P sandpaper. Clean surface with solvent based wax and grease remover or isopropanol, ensuring surface is free from dust, grease, oil and contaminants.  TXT can be applied direct to Rigid plastic /fiberglass surfaces.
Flexibly plastics - abrade with a minimum 180-240P sandpaper, clean surface with solvent based wax and grease remover or isopropanol. We recommend using a plastic adhesion promoter before applying TXT coating to ensure best adhesion.
Wood – TXT can be applied directly to wood, avoid using liquid solvents to clean, make sure wood is dry and free from dust and contaminants.   

MIXING
Invert and shake the can thoroughly until the agitation ball can be heard - 2 to 3 minutes, continue to shake the can during application.

APPLICATION
DO NOT APPLY BELOW 5°C
Application
– Spray in an even overlapping pattern approximately 20-25cm (8-10inches) in distance, apply a minimum of 2 coats
Apply 2 to 3 even coats to gradually increase film thickness. Avoid heavy wet coats to minimise risk of runs.
Allowing flash off between coats of 10mins @ 25°C (in colder conditions increase time frame between coats)

DRY FILM BUILD (theoretical)
1 x Coat = 50-75µm, 1.9-2.9.0mils (0.05 – 0.07mm)

DRY TIME
Touch dry in 3-4hrs @25°C, allow 5-7 days for full cure with exposure to UV
Dry time can be reduced by baking, not recommended exceeding 60°C

COVERAGE
Approximately 1.5 m2 (60 ft2)/300g at minimum recommended Dry Film Thickness

CLEAN UP
To clean the can turn upside down and spray until the jet clears.
Any over spray can be cleaned with mineral turps.

STORAGE
Keep in a well-ventilated area at room temperature away from direct sunlight.

Customer Reviews

Write a product review

Car audio loves it

By: on 11 October 2025
⭐️⭐️⭐️⭐️⭐️ Review for Car Builders Australia TXT Aerosol Texture Coat Just tried out the Car Builders TXT Aerosol Texture Coat, and I’m seriously impressed. I used it to finish my custom A-pillars for a car audio setup, and the result looks like tough factory — clean, even texture with a tough, professional feel. The coverage is great, it dries fast, and it’s easy to control the finish depending on how heavy you spray. It’s honestly the perfect product for car audio guys who want that OEM-style texture without messing around with expensive spray guns or complicated prep. My next project will be coating my subwoofer enclosure with this stuff — can’t wait to see how it turns out! Highly recommend this for anyone doing custom interior or audio work who wants that premium textured finish.

11/10/2025